Rohtak · Haryana · IndiaSince 2003

Two units · one supplierCHQ wire & bright bars

Installed capacity5,500 MT / month

Certified quality systemISO 9001:2015

Rohit SteelsMore out of steels · A unit of Nikhar Group

Press → to skip

RohitSteels

More out of steels · A unit of Nikhar Group

Cold heading quality wire and bright bars, made so that every coil and bar you receive behaves the same way on your line as the last one.

Established2003

LocationRohtak, Haryana

CertificationISO 9001:2015

Capacity5,500 MT / month

Rohit Steels · since 2003

Twenty-three years of more out of steel

Rohit Steels was founded in Rohtak in 2003 to give cold forgers and component makers one dependable source for CHQ wire. Over two decades the plant has grown line by line — pickling, spheroidized annealing, seven automated drawing machines — and in 2020 a second unit was added so the same customers could buy bright, ground and peeled bars from the supplier they already trusted.

2003Unit-I commissioned at HSIIDC, Hisar Road — CHQ wire drawing begins.

2003 – 2019Pickling & phosphating line, 30 T and 7 T bell furnaces and seven drawing machines take Unit-I to 4,000 MT / month.

2020Unit-II at IMT Rohtak opens for bright, ground and peeled bars — 1,500 MT / month.

Today5,500 MT / month across both units, ISO 9001:2015, serving 200+ customers in automotive, tractor, fastener and general engineering.

INSTALLED CAPACITY · MT / MONTH

0

Installed capacity by year; Unit-I build-up 2003 – 2019, Unit-II added 2020.

0

Years in steel

0

Units in Rohtak

0+

Customers served

Infrastructure

Two units in Rohtak, one point of contact

Unit-I · HSIIDC, Hisar Road

Rohit Steels — Unit-I

CHQ wire · pickling & phosphating · spheroidized annealing · wire drawing

Capacity: 0 MT / month wire drawing
Address: Plot No. 84, 85, 86 & 116, HSIIDC, Hisar Road, Rohtak — 124001

Unit-II · IMT Rohtak

Rohit Steels — Unit-II

Bright bars · ground bars · peeled bars · hex & profile bars

Capacity: 0 MT / month bright, ground & peeled bars
Address: Plot No. 14 & 25, IMT, Rohtak — 124001

Interactive site plan

Walk the two plants — click any building

SELECT A BUILDING

Rohit Steels · Rohtak

Unit-I on Hisar Road makes CHQ wire; Unit-II at IMT makes bright, ground and peeled bars. Click a building in the plan, or pick one from the list, to see what happens inside.

Inside the plant

Plant walkthrough · Unit-I

A short film shot inside Unit-I — the coil yard, the pickling and phosphating line, the bell-type annealing furnaces and the wire drawing section your CHQ wire comes from.

The film keeps playing in the corner as you move through the next slides.
Press V at any time to hide or bring back the player.
Press M to mute or unmute.

Unit-I · HSIIDC, Hisar RoadCHQ wire plantCorporate film · 5 min 32 s

What you can buy from us

CHQ wires & bright bars

CHQ Wires

Cold heading quality wire in every grade you forge — pickled, phosphated, spheroidize-annealed and drawn to your exact size — so it feeds your headers without die wear, cracking or surprises.

Ø 2 – 40 mmAll grades4,000 MT/monthPhosphated + lube coatedSpheroidize annealed

Bright, Ground & Peeled Bars

Round, hex, square and profile bars that arrive straight, clean and within tolerance — ground or polished where your parts need it, MPI-checked so hidden defects never reach your machines.

Ø 3 – 60 mmRound · Hex · Square1,500 MT/monthCenterless groundMPI tested

Unit-I · Process flow

From wire rod to ready-to-head CHQ wire

Unit-I · Facility 01

Pickling & phosphating line · 4,500 MT/month

Before your wire is drawn, every coil is acid-pickled to strip mill scale, jet-washed clean and phosphated. The result is a surface that draws smoothly, takes lubricant evenly and protects your cold-forging dies — so you see longer die life and fewer surface rejects on your parts.

Nine stages run as one continuous coil line, with D.M. water rinsing before lube coating so no acid or salts are carried into your process.

01De-binding

02Acid pickling

03Jet washing

04Water dipping

05Activation

06Phosphating

07D.M. watering

08Bond lube coating

09Drying

Unit-I · Facility 02 · Bell-type furnaces

Spheroidized annealing · 1,800 MT/month

SCADA · ANNEAL CYCLE 720 °C

30-ton furnace

900 MT/month

Your large orders are annealed in one batch, so every coil in the lot has the same structure and hardness.
3 bases and 2 bells, run by expert supervisors with real-time SCADA tracking of every annealing cycle.
Wire sizes 3.50 mm – 36 mm, all grades.

7-ton bell-type furnace

800 MT/month

Small and urgent lots get their own cycle — no waiting for a big batch to fill.
8 bases and 6 bells handled by a team of experts with SCADA monitoring for quality control.
Wire sizes 2.30 mm – 30 mm, all grades.

Unit-I · Facility 03

Wire drawing on seven automated machines

Any size from 2 to 40 mm, on the machine best suited to it — 4,000 MT/month of capacity behind your schedule.
Finished coils wait in a marked FG stock area, then are packed and wrapped to your specification.
Delivered by Rohit Steels' own logistics, or by a transporter supervised by Rohit Steels, so it arrives on time and undamaged.

Machine	Min	Max
Wire Draw IVD-600	3 mm	7 mm
Wire Draw IVD-800	5 mm	13 mm
Wire Draw IVD-900	8 mm	20 mm
Wire Draw IVD-1200	20 mm	40 mm
Wire Draw Bull Block	16 mm	28 mm
Wire Draw Bull Block (Mini)	5 mm	13 mm
Wire Draw 4-Block (Multi)	1.9 mm	7 mm

Unit-II · Bar plant

Bright bars for component manufacturing industries

Unit-II was set up in 2020 so customers who already buy CHQ wire from us could source bright, ground and peeled bars from the same supplier — automotive, tractor, fastener, hydraulic and general engineering shops alike. Sizes and finishes follow what your parts need, not a fixed catalogue.

Current output vs. installed capacity1,200 / 1,500 MT per month

Customised size ranges on demand — 300 MT/month of headroom is available for your new programmes.

Unit-II · IMT Rohtak

Annealed bar

Peeled & ground bar

Bright bar

Hex bar

Profile bar

Unit-II · Process flow

From wire rod to finished bright bar

Unit-II · Facility 01

Combined drawing lines with automatic shot blasting

3 combined drawing lines with automatic shot blasting give you a clean, bright finish in sizes 3 – 28 mm.
3 draw benches cover 22 – 60 mm, with band saws and straighteners for cut lengths to your drawing.
A chamfering machine, added at customers' request, delivers bars ready to load in your machines.

Combined drawing line · coil to cut bar

CDL machine · section	Min	Max	Speed
Old CDL machine
Round	7 mm	13 mm	40 m/min
Hex	6 mm	13 mm	40 m/min
New big CDL machine
Round	10 mm	28 mm	30 m/min
Hex	10 mm	24 mm
Square	10 mm	24 mm
New small CDL machine
Round	7 mm	15 mm	50 m/min
Hex	6 mm	13 mm	50 m/min

Unit-II · Facility 02

Grinding, polishing & material handling

Centerless through-feed grinding

Finishing

The bar is fed lengthwise between a fast grinding wheel and a slow regulating wheel — 3 centerless grinders leave a smooth, defect-free surface.
Polishing gives the finish your components show on the outside, straight from the bar.

Cantilever racks · EOT crane handling

Material handling

Your material is stored on marked cantilever racks under 5S discipline — no mix-ups between grades or customers.
Loading and unloading by EOT cranes, so bars are never dragged or dented on the way to your truck.

Unit-II · Sustainability

Powered by the sun · 500 kW rooftop solar

A 500 kW rooftop solar plant on Unit-II supplies clean power to the bar plant during the day, so a growing share of every bar you buy is made with energy generated on our own roof.

0kW

Installed capacity

≈0lakh kWh/yr

Solar generation

≈0t CO₂/yr

Emissions avoided

Generation and CO₂ figures are indicative, based on typical Haryana solar yield (≈1,400 kWh per kW per year) and India's grid emission factor.

Lower and more predictable energy cost per tonne — protection against grid tariff increases.
Supports customers' own Scope 3 and supplier-sustainability reporting.

Unit-II rooftop · solar array

Representative list — confirm before audit

What we supply

Grades & size catalogue — filter by family

Grade	Family	Size range	Condition supplied	Typical applications
SAE 1006 / 1008 / 1010	Low carbon	2 – 40 mm	Annealed · phosphated	Rivets, screws, cold-headed pins
SAE 1015 / 1018 / 1022	Low carbon	2 – 40 mm	Spheroidize annealed	Bolts, studs, hex nuts
10B21 / 10B33	Boron	5 – 32 mm	Spheroidize annealed	High-tensile bolts (8.8 / 10.9)
15B25 / 20MnB4	Boron	6 – 30 mm	Spheroidize annealed	Wheel bolts, chassis fasteners
35C8 / SAE 1035 / 1541	Medium carbon	6 – 36 mm	Spheroidize annealed	Axle studs, ball pins, shafts
EN8 / EN9 / C45	Medium carbon	6 – 60 mm	Annealed · bright · peeled	Shafts, pins, machined parts
20MnCr5 / SAE 8620	Case-hardening alloy	6 – 60 mm	Annealed · peeled & ground	Gear blanks, transmission parts
40Cr4 / SCM435 / SAE 4140	Alloy	6 – 60 mm	Spheroidize annealed · bright	High-strength bolts, tie rods
EN19 / 42CrMo4	Alloy	10 – 60 mm	Annealed · bright · ground	Hydraulic rods, precision shafts
Stainless 304 / 316 *	Stainless	3 – 25 mm	Bright	Corrosion-resistant fasteners

Sizes shown are drawn wire / bright bar diameters. * Stainless on request. Other grades available against confirmed chemistry.

Quality

In-house laboratory & testing equipment

Every lot you receive has been checked in our own lab at each stage — chemistry, hardness, microstructure and dimensions — and full-length MPI inspection catches sub-surface defects before a bar reaches your machines. Test certificates travel with the material.

SpectrometerUniversal testing machineHydraulic press · 250 MTMetallurgical microscopeStereo microscopeImage analyzerRockwell hardness testerCut-off sample machineBelt grinderMounting pressPolishing machineMuffle furnaceMagnetic particle inspection

0 HRCRockwell hardness

0 MPaTensile · UTM

± 0.01 mmDimensional check

Hardness tester

Universal testing machine

Stereo microscope

Dial gauge inspection

Quality

Quality assurance system

CERTIFICATION

ISO 9001:2015

A certified quality system across both units, so the process behind your material is audited, not assumed.

METALLURGY

Cold-forging focus

Structure and hardness tuned to how you form the part — cold forging, machining or drawing.

IDENTIFICATION

Colour-coding

Your grades carry their own colour code from receipt to dispatch, so the wrong material can never be loaded.

TRACEABILITY

Labelling system

Each coil and bundle is labelled and traceable back to its heat and mill certificate.

RECORDS

Full track record

Complete process records for every lot — available whenever your audit needs them.

PEOPLE

Qualified QA team

A qualified quality team whose measure of success is the number of complaints you never have to raise.

Sample data — replace with your 12-month figures

How we perform for customers

Delivery & quality performance

0%

On-time delivery

Orders delivered on or before the confirmed date

0PPM

Customer rejection

Parts per million rejected at customer end

0days

Complaint closure

Average time to close a customer complaint with 8D

0%

Capacity utilisation

Headroom of ~1,000 MT/month for new programmes

MONTHLY DISPATCH · MT · LAST 12 MONTHS

TREND ↑

Placeholders — send scans to replace

Documents your audit will ask for

Certificates & test reports

ISO 9001:2015Quality management system certificate — both unitsSCAN PENDING

Customer approvalsSupplier approval letters & PPAP / ISIR sign-offsSCAN PENDING

Mill test certificateSample MTC — chemistry, mechanicals, heat numberSCAN PENDING

Annealing cycle reportSCADA cycle chart with soak temperature and timeSCAN PENDING

MPI inspection reportFull-bar magnetic particle inspection recordSCAN PENDING

Calibration recordsLab instrument calibration certificatesSCAN PENDING

Rotates automatically · use ↑ / ↓ to turn

How we work with a new customer

From first enquiry to regular supply

Enquiry

Share your drawing, grade, size and monthly volume. We confirm feasibility and the route — wire or bar, condition and finish — usually the same day.

Sample & trial lot

A trial quantity with full test certificate, so your line can prove it out before any commitment.

Approval

PPAP / ISIR documentation, chemistry and mechanicals matched to your specification, colour code assigned to your grade.

Regular supply

Scheduled dispatches on our own logistics, traceable lot by lot, with MTC and packing list on every consignment.

Feedback & improvement

Complaint handling with 8D within days; die-life and rejection data reviewed with you to keep improving the material.

WITH EVERY LOT

Test certificate & packing list

Chemistry, mechanicals and heat number travel with the material, so your incoming inspection is a check, not a hunt.

ALWAYS

Colour-coded, traceable material

Your grade keeps its own colour code from our coil yard to your store — no mix-ups, full traceability back to the mill.

ONE CONTACT

Wire and bars from one supplier

One commercial contact, one quality team and one logistics fleet across both units, whatever mix of wire and bar you buy.

Partners

Who trusts us & where our steel comes from

AutomotiveTwo-wheelersTractors & farm equipmentFastenersBearingsHydraulicsConstruction equipmentGeneral engineeringDefenceAutomotiveTwo-wheelersTractors & farm equipmentFastenersBearingsHydraulicsConstruction equipmentGeneral engineeringDefence

0+customers

CLIENTS WE PROUDLY SERVE